Cloud Ivory Floor Tile

500mm X 500mm, Shiny Finish
Product Code: FS1CDC11501
R94.90/M2 (incl. VAT)
Back to Section Links
Ophelia Green Border

500mm X 110mm, Matt/Shiny Finish

R74.90/EA (incl. VAT)
Ophelia Green Border
Ophelia Green Corner

110mm X 110mm, Floor Insert

R24.90 (incl. VAT)
Ophelia Green Corner
Rocky Mountain Pebble Sand

300mm X 300mm, Resin Mosaic

R59.90/EA (incl. VAT)
Rocky Mountain Pebble Sand
Back to Section Links


Glossy ceramic tiles provide an easy way to take plain spaces and transform them into great living spaces.

The shiny surface brings depth and colour into your room.

They are great for bedroom, kitchen and dining areas and look beautiful on walls too.

The shiny surface is easy to clean.

CTM offers a wide range of glossy shiny tiles.

Technical Information

Tile Type
Ceramic Floor & Wall Tile
Tiles per Box
8 tile(s)
Square Meters per Box
2 m2
500 mm
500 mm
8.2 mm
Recommended for residential floor and wall applications.

How to install


  • Make sure that surface is dry, clean, flat and firm. Do not tile on old floor coverings like vinyl tiles.
  • Check screen, substrate and foundation are set for tiling.
  • Make sure there are expansion joints in the screed.


  • Buy enough tiles to cover the required area – get 10% to allow for cutting and breakages.
  • Make sure all the boxes have the same shade number, and that all the tiles, are the same colour, size and are clear of defects.
  • Tip: Mix 4-5 boxes prior to laying to minimize any possible shade variation.


  • Start tiling in the middle of the area.


  • Make sure you’re using the correct adhesive for the application.
  • Check screen, substrate and foundation are set for tiling.
  • Apply adhesive evenly using a notched trowel. ( Apply 1m2 at a time)
  • Only mix enough adhesive to use within 1 hour.
  • Work over small areas so the adhesive does not dry.
  • Scrape away excess adhesive, separating each tile from the next.
  • All tiles must be fully embedded using a rubber mallet.


  • Start off by creating building lines in your work space. This will allow you to achieve straight lines.
  • Do not butt join tiles. Spacing is 5mm-8mm.( Please use spacers)
  • When tiling large areas. Create expansion joints to allow for structural movement.
  • This is done by using a flexible compound (such as silicone) between tiles.
  • Expansion joints should be made every 9m2.
  • The perimeter joint needs to be 5-8mm.


  • Make sure all the joints are clean.
  • Apply the grout using a rubber squeegee.
  • Grouting should be done 24 hours after the installation of the tiles to allow, the tile to set properly.
  • Once the grout has set the entire area must be cleaned,
  • With a damp cloth, Grout Off and Easy Clean, Cleaning agents are recommended.
  • Avoid walking on the tiles for 2-3 days to prevent loosening of the tiles.

Back to Section Links
Progrip Dove Grey Waterproof Grout 5Kg

Water Resistant Grout Covers 8-11m2

R49.90 (incl. VAT)
Progrip Dove Grey Waterproof Grout 5Kg
Basecoat 5Kg

Combine With Key Coat For Surface Prep

R44.90 (incl. VAT)
Basecoat 5Kg
Key Coat 5Lt

Primer For All Types Of Surfaces

R199.90 (incl. VAT)
Key Coat 5Lt
Tile Spacers 5mm

5mm Spacers Covers 10m2

R14.90 (incl. VAT)
Tile Spacers 5mm
Progrip Flexigrip Adhesive 20Kg

For Interior & Exterior Tile Applications

R52.90 (incl. VAT)
Progrip Flexigrip Adhesive 20Kg
Aluminium Straight Edge

10mm X 2.5m, Edge Trim

R49.90 (incl. VAT)
Aluminium Straight Edge
Back to Section Links
Block Brush Synthetic 190mm

Used For Surface Preparation & Cleaning

R34.90 (incl. VAT)
Block Brush Synthetic 190mm
Back to Section Links